Shopping Cart
Your Cart is Empty
Quantity:
Subtotal
Taxes
Shipping
Total
There was an error with PayPalClick here to try again
CelebrateThank you for your business!You should be receiving an order confirmation from Paypal shortly.Exit Shopping Cart

 PARKER'S SAFES & VAULTS 

Tennessee gun safe, Nashville safe, best safe, Amsec, vault doors, best place to buy a safe, graffunder, gun safe, AMERICAN SECURITY, best gun safe, best fire safe, security, most secure safe, safe moving, Alabama gun safe, Georgia gun safe, military safes, vaults gun vaults, the best safe, secure 

-Since 2009

PARKER'S SAFES AND VAULTS has specialized in high quality safes and vault doors. We're a Veteran-owned, family-run, business. Our product lines include,  GRAFFUNDER, AMERICAN SECURITY, ISM, RHINO, GARDALL, OLD GLORY, HAYMAN and more...

We offer in home delivery and installation and ship nationwide. 


[email protected]

164 Cessna Lane

Shelbyville, TN 37160

931.842-6445


PLEASE CALL BEFORE VISITING AS WE MAY BE ON A DELIVERY! 932.842-6445

Installing an AMSEC INSWING VAULT DOOR.

Remember, this is for an INSWING DOOR. The door doesn't need to be removed for an outswing door.


American Security makes a great door. It has a solid 1/2" plate with a 1- 1/8" layer of their proprietary dry-lite concrete type mixture behind that. This combo makes for a very formidable door but the installation is a bit tough sometimes.

Here's how we address some of the problems with their design.


1. Toss out the instructions that come with the door! Well, you can read them if you want, but they won't apply if you are installing the door into a concrete jamb.

2. Put all the tools and materials you'll need as well as the interior frame inside the vault room. The tools required inside would be a couple flashlights or work lights, a small sledge hammer, a ball pein hammer, a prybar or two, some 2x4's to use as cribbing under the door that you'll remove and for a fulcrum for your prybar, a 3/8" allen wrench, (an allen socket and flexible extension for a cordless impact would help) a cordless drill and impact, a 6' level, a quick- grip clamp or two, a few 3/16" punches about 3" long (make sure these are hardened steel and that the 3/16" shaft part is about 3" long to drive the hinge pin all the way out of the hinge barrel) a 3/8"punch, a few 3/8" steel drill bits, a few 1/4" concrete/ masonry bits, 16 (sixteen) 1/4" x 3 1/2" Simpson Strong Tie Titen HD concrete anchors, a 3/8" socket, and some cardboard and duct tape, You'll also want an assistant to help move the door once it's off its hinges, If you forget something, no worries, you can just open the door a bit and have someone on the outside pass it to you. 

3. Station yourself and an assistant inside the vault room and have some help position the door into place with the outer frame snug against the outside wall.

4. Tape about a square foot of cardboard to the door and frame above each hinge to protect the paint while you are trying to beat the hinge pins out of the hinge. Trust me, just do it or you'll be touching up the paint. (The door comes with touch up paint though so suit yourself.)

5. Use the 3/8" allen wrench to remove the set screw and ball bearing  from the bottom of the hinge. (Note how they come out, one side is beveled)

6. Use the 3/16" punch to drive the hinge pin down from the top of each hinge. Yep, this is the hard part. You may have to get creative with the prybar and perhaps the small sledge hammer for the top hinge because there's little room to work.

7. Use the prybar and 2x4's to remove the door from the frame. Set the door aside carefully and with help for now by leaning it against the wall.

8. Use a little piece of duct tape and cover the hinge pin hole on the jamb. This will prevent any metal shavings from falling in there while you are drilling the steel frame.

9. Place the steel, U-shaped, interior frame trim piece in place behind the door frame. It should overlap if the the rough opening is less than 9.5 inches.

10. Use the level to plumb the jamb and secure it in place with the quick grip clamps. CHECK PLUMB BOTH DIRECTIONS AND ADJUST ACCORDINGLY.

11. Use the 3/8" steel bit and drill holes through the interior frame at the top and bottom corners by using the access holes in the main frame as a pilot. Be careful not to drill into the concrete or you'll ruin your bit. Check plumb both ways while you do this to ensure nothing has shifted.

12. Use the 1/4" masonry bit to predrill the corner holes for the Titen Anchors.

13. Do the same to predrill the remaining anchor points. 

14. Don't tighten the anchors all the way until the door is back on the hinges, but run the Titen anchors into the jamb to secure it to the frame. TAKE CARE TO NOT OVERTIGHTEN AND DISTORT THE FRAME.

15. Re-hang the door. You can use the 3/8" punch to drive the pins back up into the hinge barrel. Then install the ball bearing and Allen set screw.

16. Tighten the anchors but TAKE CARE TO NOT OVERTIGHTEN AND DISTORT THE FRAME.

17. Check the door boltworks. If there is any friction or interference, you might be able to address that by adjusting the allen set screws. 

18. Please let us know if these instructions helped or need edited! Aaron Parker 931.842-6445

19. Call AMERICAN SECURITY after you've calmed down and politely ask them to redesign their vault door frame and mention how cool a clam-shell frame would be. 



 














BLOG/INFO

BLOG/INFO

view:  full / summary

Our farewell letter to CHAMPION and SUPERIOR

Posted on October 28, 2020 at 12:55 AM

Greetings Ray,

Since you sent me back to Flagstaff with my first safe in 2008, Champion and Superior Safes have been our best-selling lines. We’ve been through a lot together including, product design, name changes, the development of your vault doors and more. Over the years, it’s been easy to promote and sell Champion and Superior products. Unfortunately, things seem to be changing. Consider the old Master, our best seller since the beginning.

It was heavier than si...

Read Full Post »

Gun safe- shipping nationwide

Posted on July 4, 2014 at 12:40 AM

If you decide to purchase a gun safe or other safe online, here are a few things to consider. First, FREE-SHIPPING is seldom really free. There is a significant spectrum of freight charges/prices from one freight company to another, but they all have to pay drivers, pay dock and office workers, maintain vehicles, etc. It might seem like you're saving money as you add a safe to your online shopping cart, but do you think there's really a freight company in business who doesn't charge for thei...

Read Full Post »

Why are we here?

Posted on February 17, 2014 at 10:35 PM

Here's a brief history of how I got involved with safes. I have an Uncle, Larry Parker in Ohio, who's been selling safes for about 25 years. Some of you may be familiar with his work as a Master hammer and chisel engraver and riflebuilder. He's developed quite a reputation in that arena.

Anyway, about 6 years ago, I asked him what it would take to get involved in the safe business. I was working as a finish carpenter in Flagstaff, AZ. at the time. He said, "Well, I'll get back with you....

Read Full Post »

My Safe Will Explode!

Posted on October 18, 2013 at 9:10 PM

                                                                                             STORING AMMUNITION IN YOUR SAFE

Hollywood has done a great job making us believe that when burned, ammunition will explode and fire as if it were in a firea...

Read Full Post »

Customer Questions

Posted on October 18, 2013 at 9:00 PM

Greetings from PARKER'S SAFES AND VAULTS of Tennessee.

I get a lot of questions from folks who are in the market for a gun safe. I thought I'd take a few minutes and address a couple of those. (I'll be the first to admit that I'm a little biased, but my opinions are based on my personal experience. I have delivered, installed and serviced a lot of safes)

Okay, so here goes...

First question...

 

1. There is so much information on the web and so many compani...

Read Full Post »

Are Your Valuables Protected?

Posted on October 18, 2013 at 8:55 PM

QUESTION- When is the best time to buy a quality safe?

ANSWER- BEFORE something not-so-good happens to your stuff.

 

A safe isn't the most enjoyable thing to spend your money on. It might not even register on the fun scale. Having a safe though is a good feeling. I bought my first safe, a Liberty, about 15 years ago when Ray Crosby still owned the company. Picking out the safe was kind of fun, getting it into our house, umm- not so much fun. Loading it with my firearms...

Read Full Post »

Rss_feed